JOHN DEERE 3350 John Deere Models: 3005 thru 4995

INCLUDES: PPA & 5 PAD ENGINE DISC
FLYWHEEL STEP: .850"

NEW LUK
INCLUDES: PPA AND 5 PAD ENGINE DISC
FLYWHEEL STEP .850"

FLYWHEEL STEP: .850"

FLYWHEEL STEP: .850"

NEW LUK, FLYWHEEL STEP: .850"

INTERCHANGEABLE WITH 333 0042 10
(NEW AVAILABLE)

INTERCHANGEABLE WITH 333 0042 10

NEW LUK
INTERCHANGEABLE WITH R68022

(NEW AVAILABLE)

GREASEABLE, SELF CENTERING BEARING WITH CARRIER

3 PORT SLAVE CYLINDER AND RELEASE BEARING ASSEMBLY
MUST USE BRAKE FLUID ONLY ---- DO NOT USE HYDRAULIC OIL
CAN USE FOR 2 PORT IF YOU GET M 10x1 PIPE PLUG L41876 & L39222 O-RING

2 PORT SLAVE CYLINDER AND RELEASE BEARING ASSEMBLY
MUST USE BRAKE FLUID ONLY ---- DO NOT USE HYDRAULIC OIL

SIZE: 12 7/8", INCLUDES: RING GEAR, FLYWHEEL ID 13.030"

142 TOOTH RING GEAR

23CM (1.38 CI) HYDRAULIC PUMP WITH KEYED SHAFT

(R97872 NEW AVAILABLE);
THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

23CM (1.38 CI) HYDRAULIC PUMP WITH KEYED SHAFT;
(NEW AVAILABLE)

FITS: 0.7 C.I. (12cc) & 1.4 C.I. (23cc) PUMPS

USE WITH R39319 SHAFT

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R34348 SHAFT

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R39319 SHAFT
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

USE WITH R39319 SHAFT

INCLUDES: MOUNTING GASKET & BACKPLATE GASKET, FOR MODELS WITH REMOTE COOLANT TANK; HAS BANJO FITTING HOLE

ONE PIECE TEFLON SEAL AND WEAR SLEEVE ASSEMBLY
SUB FOR AT22965, AR92893, RE11036, RE17831, RE24959

AFTERMARKET

NEW AP AIR DESIGN 6E171 COMPRESSOR WITH LATE DENSO 10PA17 INTERNAL DESIGN.
CAN RE-USE ORIGINAL MANIFOLD. FOR MANIFOLD REPLACEMENT KIT, ORDER 451-1173K.
CAN USE STANDARD DUTY DENSO STYLE - 503-116
CAN USE HD SANDEN STYLE COMPRESSOR - 503-117 WILL NOT FIT JOHN DEERE MODELS 2250, 2450, 2650, 2650N, 2850, 2355, 2555, 2755, 2855N, 2955, 3050, 3350, 3650, 3055, 3155, 3255 WITH JOHN DEERE AL63652 COMPRESSOR MOUNTING BRACKET.

CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.