JOHN DEERE 2250 John Deere Models: 1010 thru 2955

FLYWHEEL STEP: 2.200" - 2.210", INCLUDES: PPA, 6 PAD ENGINE DISC AND WOVEN PTO DISC, INTERCHANGEABLE WITH R55140U

INCLUDES: PPA, 6 PAD ENGINE DISC & WOVEN PTO DISC
FLYWHEEL STEP: 2.200" - 2.210"
INTERCHANGEABLE WITH R27706U

NEW LUK
INCLUDES: WOVEN PTO DISC
INTERCHANGEABLE W/R55140 & R27706
FLYWHEEL STEP 2.200" - 2.210"

INTERCHANGEABLE WITH R55140 AND 228 0023 10,
INCLUDES: WOVEN PTO DISC,
FLYWHEEL STEP 2.200" - 2.210",
(NEW AVAILABLE)

INCLUDES: WOVEN PTO DISC,
FLYWHEEL STEP 2.200" - 2.210"

INCLUDES: WOVEN PTO DISC
FLYWHEEL STEP: 2.200" - 2.210"
INTERCHANGEABLE WITH R27706 & 228 0023 10

INTERCHANGEABLE WITH 328 0061 10 & 328 0061 11

NEW LUK,
SPRING CENTER,
INTERCHANGEABLE WITH R66923

NEW LUK
INTERCHANGEABLE W/R66923

INTERCHANGEABLE WITH 323 0084 10

FITS: R55140 PPA
KIT INCLUDES: 3-CAST STYLE RELEASE LEVERS, 3-LEVER SPRINGS, 3-LEVER PINS, 3-PUSH PINS, 6-LEVER PIN CLIPS & 3-ROLL PINS
NOTE WHEN REPLACING STAMPED STEEL LEVERS THE PTO RELEASE PIN GUIDES ON THE BACKPLATE BELOW THE LEVERS MUST BE MACHINED DOWN FROM .550" TO .080" ABOVE BACKPLATE.

NEW LUK
INTERCHANGEABLE WITH R39592
FLYWHEEL STEP: .850"

FLYWHEEL STEP: .850"

NEW LUK

GREASEABLE, SELF CENTERING BEARING WITH CARRIER

3 PORT SLAVE CYLINDER AND RELEASE BEARING ASSEMBLY
MUST USE BRAKE FLUID ONLY ---- DO NOT USE HYDRAULIC OIL
CAN USE FOR 2 PORT IF YOU GET M 10x1 PIPE PLUG L41876 & L39222 O-RING

2 PORT SLAVE CYLINDER AND RELEASE BEARING ASSEMBLY
MUST USE BRAKE FLUID ONLY ---- DO NOT USE HYDRAULIC OIL

SIZE: 12 7/8", INCLUDES: RING GEAR, FLYWHEEL ID 13.030"

142 TOOTH RING GEAR

23CM (1.38 CI) HYDRAULIC PUMP WITH KEYED SHAFT

(R97872 NEW AVAILABLE);
THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

23CM (1.38 CI) HYDRAULIC PUMP WITH KEYED SHAFT;
(NEW AVAILABLE)

1 1/16" MALE O-RING x 7/8" MALE JIC

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

FITS: 0.7 C.I. (12cc) & 1.4 C.I. (23cc) PUMPS

USE WITH R39319 SHAFT

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R34348 SHAFT

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R39319 SHAFT
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

USE WITH R39319 SHAFT

ONE PIECE TEFLON SEAL AND WEAR SLEEVE ASSEMBLY
SUB FOR AT22965, AR92893, RE11036, RE17831, RE24959

R12 & R134A COMPATIBLE

AFTERMARKET

NEW AP AIR DESIGN 6E171 COMPRESSOR WITH LATE DENSO 10PA17 INTERNAL DESIGN.
CAN RE-USE ORIGINAL MANIFOLD. FOR MANIFOLD REPLACEMENT KIT, ORDER 451-1173K.
CAN USE STANDARD DUTY DENSO STYLE - 503-116
CAN USE HD SANDEN STYLE COMPRESSOR - 503-117 WILL NOT FIT JOHN DEERE MODELS 2250, 2450, 2650, 2650N, 2850, 2355, 2555, 2755, 2855N, 2955, 3050, 3350, 3650, 3055, 3155, 3255 WITH JOHN DEERE AL63652 COMPRESSOR MOUNTING BRACKET.

CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.