JOHN DEERE 401C John Deere Models: 105 thru 595

FLYWHEEL STEP: FLAT

GREASABLE

INCLUDES: PPA, WOVEN DISC, RELEASE & PILOT BEARINGS
FLYWHEEL STEP: 1.480"

FLYWHEEL STEP: 1.480"
CAST # 170C142

GREASABLE

INTERCHANGEABLE WITH D1163702
FLYWHEEL STEP: FLAT

INTERCHANGEABLE WITH D1145308
FLYWHEEL STEP: FLAT

INTERCHANGEABLE WITH 328 0061 10 & 328 0061 11

NEW LUK,
SPRING CENTER,
INTERCHANGEABLE WITH R66923

NEW LUK
INTERCHANGEABLE W/R66923

GREASABLE

FLYWHEEL STEP: 2.200" - 2.210", INCLUDES: PPA, 6 PAD ENGINE DISC AND WOVEN PTO DISC, INTERCHANGEABLE WITH R55140U

INCLUDES: PPA, 6 PAD ENGINE DISC & WOVEN PTO DISC
FLYWHEEL STEP: 2.200" - 2.210"
INTERCHANGEABLE WITH R27706U

NEW LUK
INCLUDES: WOVEN PTO DISC
INTERCHANGEABLE W/R55140 & R27706
FLYWHEEL STEP 2.200" - 2.210"

INTERCHANGEABLE WITH R55140 AND 228 0023 10,
INCLUDES: WOVEN PTO DISC,
FLYWHEEL STEP 2.200" - 2.210",
(NEW AVAILABLE)

INCLUDES: WOVEN PTO DISC,
FLYWHEEL STEP 2.200" - 2.210"

INCLUDES: WOVEN PTO DISC
FLYWHEEL STEP: 2.200" - 2.210"
INTERCHANGEABLE WITH R27706 & 228 0023 10

INTERCHANGEABLE WITH 328 0061 10 & 328 0061 11

NEW LUK,
SPRING CENTER,
INTERCHANGEABLE WITH R66923

NEW LUK
INTERCHANGEABLE W/R66923

INTERCHANGEABLE WITH 323 0084 10

FITS: R55140 PPA
KIT INCLUDES: 3-CAST STYLE RELEASE LEVERS, 3-LEVER SPRINGS, 3-LEVER PINS, 3-PUSH PINS, 6-LEVER PIN CLIPS & 3-ROLL PINS
NOTE WHEN REPLACING STAMPED STEEL LEVERS THE PTO RELEASE PIN GUIDES ON THE BACKPLATE BELOW THE LEVERS MUST BE MACHINED DOWN FROM .550" TO .080" ABOVE BACKPLATE.

GREASABLE

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON THE MOUNTING FLANGE LEFT SIDE , A 7/8" PRESSURE PORT IN THE PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON THE BOTTOM. IT DOES NOT HAVE AN INLET PORT ON THE MOUNTING FLANGE RIGHT SIDE.
NOTE: THE INDICATED SIDES OF PUMP ARE AS SEEN FROM THE TRACTOR SEAT.
IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED.

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP. IT HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. THE SIDES OF THE PUMP NOTED ARE AS SEEN FROM THE TRACTOR SEAT
NOTE: WILL SUB FOR R56160 USING DIFFERENT FITTINGS. IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R34348 SHAFT

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

INCLUDES: MOUNTING GASKET AND BACKPLATE GASKET, R932520 KIT AVAILABLE

INCLUDES: BACKPLATE GASKET & MOUNTING GASKET
R932240 KIT AVAILABLE

FITS: R54805, R55130, R55164 & R59049 INCLUDES: 2 GASKETS, SPRING SEAL, BEARING & IMPELLER

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

ONE PIECE TEFLON SEAL AND WEAR SLEEVE ASSEMBLY
SUB FOR AT22965, AR92893, RE11036, RE17831, RE24959